Are you a handyman? Are you more artistically inclined? Do you like the thought of making beautiful things from wood? If so, you are like many other people that take pleasure in creating with wood. The key to having fun with woodworking is knowing some tips to help, which is what this article is going to show you.
Tape can be your friend when gluing stained wood together. Place the two pieces of wood together in a clamp and tape the seam before applying the glue. Carefully cut the tape along the joint and then separate the two pieces of the wood and apply the glue along the joint. Clamp together and allow to dry. The tape will keep the glue off the wood and is easy to remove once the glue is dried.
Check out your local library for books on woodworking. You will likely find books that contain tips, special skills or even step-by-step guides that can take you from start to finish on a project. A library can be wonderful source of information that people tend to forget when they are looking for knowledge, so do not let this resource slip your mind.
Learn more about different kinds of wood and their characteristics. Every piece of wood is different. Different types of wood will stain differently. Different cuts will splinter differently. There are many varieties of wood grains. You need to factor all of this into your project.
Before sawing, ensure that the blade is in top condition. Dull blades make sawing nearly impossible. It can also cause errors that will cost you a ton, depending on the wood type you use.
If you are working with wood, it can be very dangerous to have a messy workshop. Do everything you can to keep your work area clean and well-maintained. Every time you are done with a specific tool, out it away before you get another. It may seem like this is time consuming, but you won’t have any reason to clean up later.
Make sure that you are wearing the appropriate protective gear when you are working on your woodworking projects. Your safety is of primary importance. Eye protection can protect your eyes from flying wood debris. A pair of strong gloves can protect your hand from splinters. Make sure that you have these essentials before you start on any projects.
Take baby steps when first starting out with woodworking. It’s a lot of fun to learn, but woodworking is also pretty dangerous if you get too cocky too soon. Even when you feel like you know the basics, keep practicing them. And always where safety gear. You are much better off.
When buying wood for your woodworking project, always buy long and not to the exact measurements. Some stores will sell you wood that is cut to length. Always measure long and trim down to the exact size you need in your shop. This way if you made a minor error in measurement, you will have a little bit of extra wood to cut off or utilize to make up for the difference.
Never allow someone to watch while you are woodworking without wearing the same gear that you are wearing. Being anywhere near the tools is a hazard, even if they are not using them. Wood or parts of the tool could fly into the air and strike them just as they could you.
You can make a sanding block even better. Cut a small slot about 3/8 of inch deep, a little less than an inch from the outside edge. Run it the entire length of the block. Now the sandpaper will fit into this slot easily, and it will stay in place more securely.
When you need to finish, sand, shape, file or cut a small item, you may wish to glue it to a pedestal stick rather than attempting to clamp it. Clamps can be cumbersome when doing fine work, and sometimes, it is not even possible to use a clamp. A dot of hot glue will hold your small piece in place, and you can simply pop it free using a putty knife when finished.
If you use an orbital sander to smooth the surface of your project before finishing, move the sander very slowly. The recommended speed is one inch per second which is slower than most people sand. Going too fast can cause a small spiral pattern that does not show up until the finish is applied.
Avoid sanding with your fingertips. Instead, use a sanding block. If you can also use an electric sander. Better still, use an orbital sander. Sanding with your fingertips can cause sanding ruts. You may not notice these ruts until the project is finished. These are difficult or impossible to repair.
When driving larger nails into panels like a two by four, do you often inadvertently split the wood. You can often avoid this annoyance by using a simple trick. Turn the nail over and give the sharp end a quick rap with the hammer, dulling the tip a bit. The nail is then less likely to split the wood.
Use duct tape to easily mark level areas of your floor. If you have a table saw or other large tool on a mobile base, it can be hard to find just the right spot on your floor to keep it level. Once you have found a level location, place tape around the wheels or base of your tool so that you can easily position it the next time it is out.
There are a number of power tools you should have in your possession before starting woodworking. A driver/drill, table saw, jigsaw, power sander and circular saw are a must. Orbital sanders are great, but really any power sander will do.
As you can see, woodworking takes a bit of know-how and creativity. No matter what kind of woodworking you may be in to, having tips and tricks in your tool belt are just as important as the actual tools. Take what you have learned here and have some fun putting your skills to work.