Woodworking is a craft and a skill that has been around for centuries. It is a valuable trade to have experience with and can be infinitely useful in many ways. Skilled woodworkers can earn a good living with their hands and many enjoy woodworking just for the joy of it.
If you would like to start woodworking as a hobby or a business, always buy the highest quality tools that you can find. While you may be able to find cheaper tools, they will end up breaking during your project. Spend the extra money and buy a quality tool that will last a lifetime.
Clean your saw’s teeth before cutting lumber. To thoroughly clean your saw blade dip a shop rag into a little acetone and wipe the blade thoroughly. Additionally, using a piece of sandpaper that has a fine grit will remove any sap or gumminess from your skill saw’s cutting blades.
If you are going to be doing a big woodworking project on the outside of your home, check to make sure it is within the rules. Your local government may have zoning regulations or even a permit process needed for structures like garages, decks and even storage sheds. Also check with your neighborhood association if there is one.
You can apply stain with either a brush, or a rag. Work the stain in against the grain, and with it as well. You need not be neat, just get a smooth, even coat on the wood. Then, wipe immediately for a lighter tone, or leave it on for up to fifteen minutes before wiping for a deeper tone.
Of the surface of the wood in your project has been dinged or dented by accident, you need to remove the blemish before you finish it. If the fibers of the wood are only crushed, not torn, you can use steam to fix the problem. Fill the depression with a drop or two of water and use a hot iron over a damp cloth to level the dent.
Every good woodworking shop needs a quality combination square. It is needed for almost every job you’ll tackle. It makes a good depth gauge, using the straight side. It is, of course, perfect for miter cuts. Most have a level built right in. A good combination square is a must-have tool, right up there with a hammer and drill.
When using a table saw, use a block of wood clamped to the fence to set your length. Using the fence directly could result in a board being kicked back at you. To make measurements easy, use a block that is exactly 1 inch in length. Then all you have to do is set the fence length 1 inch greater than your desired length.
Grabbing a spring clamp and opening it one handed can be difficult. To help alleviate this problem plan ahead. Before beginning any clamping project place several spring clamps along a block of wood. This will allow you to grab the clamps one handed and hold them open while lining up the wood’s grain.
Try to learn as much you can about the new technologies available to you for your woodworking needs. Because of advances in precision tools in recent years you can likely find the things that you need so that you can do a perfect job every time that you tackle a woodworking project.
Use older or reclaimed wood whenever possible. You will not only be saving money and recycling but you will often get a better quality of wood. Many woods types are increasingly rare or more expensive but can be found but reusing older pieces of reclaimed wood that would have been discarded.
An organized toolbox is essential to a master craftsmen. Many carpenters find that using a variety of containers can keep their toolbox looking tidy. 35mm film containers are perfect for hold small fasteners and a variety of tupperware containers are perfect for holding nuts and bolts. Finally, magnetic strips can keep your screwdrivers and wrenches organized in your toolbox.
Never over-purchase when buying building supplies. If you purchase too much, often you will never find a use for everything, cluttering up your shop area by using it as storage. Instead, buy just want you need now and the things you know you’re going to actually use in the immediate future.
There are several tools that should every woodworker must have. A retractable tape measure should be in every woodworker’s toolbox. A claw hammer, a utility knife, a set of crescent wrenches and a variety of screwdrivers both phillips and flat heads should also be included in your woodworking toolbox.
Start off with small, simple projects. Choose something simple to begin with to gain experience and to get a feel for working with tools. Once you have a better grasp on how tools work and have experience with using them, you can branch out to bigger and more elaborate projects.
Don’t forget your feet if you are working with wood. A rogue nail or screw on the floor could spell disaster if it ends up embedded in your feet. Wear steel toed boots intended for the work place as they are made to keep sharp objects away from the soles of your feet, as well as keeping your toes protected from heavy objects dropped upon them.
When you are chiseling, cut away from your body. One slip could spell disaster for your hand. The same safety practice applies to using a saw. Saw away from hands and your body to avoid injury.
If you do woodworking as a hobby, don’t spend all your free time or days off on it. Get some rest once in a while and enjoy the relationships in your life. If you drive yourself too hard, you are going to make mistakes. This can produce results less than your best, or lead to accidents.
As you already know, woodworking is a very valuable skill. Whether you are building a big projects such as a house or smaller projects such as a small bird house, woodworking has so much to offer. Hopefully the tips from above have given you ideas on new ways to use this valuable skill.