Working with wood can be a great way to pass the time. Not only can you create woodworking pieces to show others, but woodworking can be a truly relaxing, calm experience. From designing the piece to sanding the final product, it can be something that you enjoy. Here are some tip to make you a better woodworker.
Tape can be your friend when gluing stained wood together. Place the two pieces of wood together in a clamp and tape the seam before applying the glue. Carefully cut the tape along the joint and then separate the two pieces of the wood and apply the glue along the joint. Clamp together and allow to dry. The tape will keep the glue off the wood and is easy to remove once the glue is dried.
Make your own reusable sanding blocks. Cut six blocks from any 3/4″ plywood you have, for each sandpaper grit you regularly use. You want them to measure about two and half inches by four and a half. Spray some adhesive on your blocks and on the cork tile. Put one block on the cork, and then cut it flush with a knife. Spray the back of a sheet of sandpaper with adhesive and adhere the cork side of the block to it. Fnally, make sure you cut sandpaper flush with the cork, and label every block.
Organize your shop’s extension cords to keep your shop safe and tidy. You can make your own cord keeper with nothing more than a scrap piece of wood. Simply cut a piece of wood in the shape of an I and wrap each of your extension cords around the wood.
Gel stains are something that you can get a lot of use out of when you’re staining items that are going to be used for furniture. Traditional liquid stains have a tendency to run. Gel stains grab on to the wood better. Also, gel stains are thick, so they tend to stain more evenly.
When you install your hacksaw blade, make sure the teeth face forward. They are designed to cut when pushed using a forward stroke instead of a pulled stroke. Some of these blades have arrows pointing toward the handles that show the correct way to install them. Install it making sure it is tight and cannot bend. When you do lots of cutting, your blade heats up and expands, so make sure you tighten it before it begins bending.
If you have loose interior door hinges to work on, you may be able to just use a golf tee to help. You need to remove both the door itself and the individual hinges from the total door frame. Then, locate each screw hole put a golf tee in each one, tapping gently. Then, cut the golf tee’s excess off and reinstall the door. This will give the screw the support that it needs.
If you are working with wood, it can be very dangerous to have a messy workshop. Do everything you can to keep your work area clean and well-maintained. Every time you are done with a specific tool, out it away before you get another. It may seem like this is time consuming, but you won’t have any reason to clean up later.
Make sure that you are wearing the appropriate protective gear when you are working on your woodworking projects. Your safety is of primary importance. Eye protection can protect your eyes from flying wood debris. A pair of strong gloves can protect your hand from splinters. Make sure that you have these essentials before you start on any projects.
Always remember the rule of measuring twice and cutting once. You are human, which means that mistakes are inevitable. However, you can prevent measurement mistakes from turning into cutting mistakes when you measure two or three times. That is going to spare you serious waste, not just in terms of wasted wood, but also money and time.
When you find a nice level spot on your workshop floor for your table saw, it can be difficult finding the same spot after you put your saw away. When you do find a level spot, use duct tape on the floor so you know where to position your table saw next time you need it.
If dust and dirt get into the holes of a brad or nail gun while they are not in use, this can cause them to wear out more quickly. It is a good idea to plug the air inlet holes up with something to prevent anything from getting in there.
If you do woodworking at home, create a well-lit, organized area in your home or garage to serve as your workshop or hobby area. Keeping your tools and supplies in one place and well-organized keeps you safer, more productive and enjoying the time spent working on your projects. This is important whether you have a large or small workshop, so set up the space with both lighting and organization at the top of your workshop to-do list.
Keep your work area as clean as possible. Woodworking creates a lot of mess, especially dust. This dust can get into your home and eventually into your lungs. This can cause real health problems down the road for you and your family. So take a few minutes after a job, and sweep up your space.
Always wear protective glasses when using any type of saw, and ear protectors as well when you use power equipment. Chips and sawdust can destroy your vision if even a small piece flies into your eye. Woodworking is a great hobby, but it is important to stay safe while you work.
Woodworking can be one of the most rewarding hobbies out there. When you see the finished piece you’ve made, it can give you a real sense of satisfaction that you can share with your loved ones. The suggestions in this article can really help you to do a great job.