Are you able to work with your hands? Do you find measuring to exact dimensions is simple for you? Would you love to be able to create useful products in your spare time? If so, the hobby of woodworking is truly for you. In fact, you might even be able to turn it into a career with the tips below.
Check out your local library for books on woodworking. You will likely find books that contain tips, special skills or even step-by-step guides that can take you from start to finish on a project. A library can be wonderful source of information that people tend to forget when they are looking for knowledge, so do not let this resource slip your mind.
Sometimes a little bit of glue is better than a clamp. Every woodworking shop should have a hot glue gun. Hot glue will hold small pieces better than any clamp ever could, if you could even maneuver one in place. When you are done, just gently pry loose with a putty knife.
Make sure that you are wearing the appropriate protective gear when you are working on your woodworking projects. Your safety is of primary importance. Eye protection can protect your eyes from flying wood debris. A pair of strong gloves can protect your hand from splinters. Make sure that you have these essentials before you start on any projects.
If you have any pockets on the shirt you are wearing, remove everything from them before you start working with a table saw. It is very common for objects like pens and rulers to fall from your pocket and get caught in the blade, which can lead to some pretty serious injuries.
Only cut using sharp tools. Older and dull tools result in tear-outs and even chipping, which is frustrating and a waste of time. Sharp tools means you get clean cuts quickly. You’ll also spend a lot less time sanding things to get just the right look and fit that you need.
You can apply stain with either a brush, or a rag. Work the stain in against the grain, and with it as well. You need not be neat, just get a smooth, even coat on the wood. Then, wipe immediately for a lighter tone, or leave it on for up to fifteen minutes before wiping for a deeper tone.
Sanding blocks are essential woodworking tools. You can create easy to reuse sanding blocks of your very own by simply cutting three-quarter-inch scrap lumber into rectangles measuring 4.75 x 4.50 inches. Cut pieces of cork tile to fit each block. Spray both the rectangle of wood and the rectangle of cork tile with adhesive and press them together. Allow to dry, then spray the backside of an entire sheet of sandpaper with adhesive. Place your newly made block on the sandpaper with the cork on the down-side. Allow to dry and then use a utility knife to cut the sandpaper around each block.
There are some basic tools needed for woodworking projects. These include a saw, hammer, files, level, square and measuring tapes. Larger pieces of equipment you may need are different types of electrical powered saws and sanders. The power tools can be quite expensive, and you may not need them unless you do a lot of woodworking projects.
You shouldn’t be applying too much pressure when sanding. Pressure can make the surface uneven. You don’t have to use force if you are using the right grit. Just gently sand in a circular motion.
When you are getting ready to glue wood together, get some packing tape ready to help you secure the wood. Packing tape is a great way to tighten up those joints so that the glue sets as perfectly as possible. Pre-cut the packing tape so that you have it handy the minute you need it.
When using a water based stain or finish to raw wood, it is a good idea to raise the grain first. Apply water to the surface just before the final sanding and wait until it dries. The wood fibers will stand and you can remove them with minimal sanding before applying the finish.
Buy quality tools. There are discount tools on the market, and you may be tempted to save some money. What is the difference? Sometimes the steel in a screwdriver is softer and can strip the screw heads. Sometimes the build quality is cheap and the head of a hammer may fly off. Spend the money for good tools and you’ll have them for decades.
Don’t throw away those old bristle brushes just because they have paint or stain material built up in them. You can remove dried stain or paint with a metal pet comb. To loosen this built up material, coat the brush’s bristles with a solvent. Next, run the teeth of the comb through the bristles. Not only will this process clean the brush, it will also help straighten out any section of the bristles which have gotten out of line.
Use older or reclaimed wood whenever possible. You will not only be saving money and recycling but you will often get a better quality of wood. Many woods types are increasingly rare or more expensive but can be found but reusing older pieces of reclaimed wood that would have been discarded.
An organized toolbox is essential to a master craftsmen. Many carpenters find that using a variety of containers can keep their toolbox looking tidy. 35mm film containers are perfect for hold small fasteners and a variety of tupperware containers are perfect for holding nuts and bolts. Finally, magnetic strips can keep your screwdrivers and wrenches organized in your toolbox.
Regardless of your current skill level, the tips above should help you improve your technique. Take each into your mind as you use them when you work. If you can integrate them into your current procedures, you’ll find that the time you spend working with wood will improve day by day.