Creating art from wood is definitely a treasured pastime of many cultures. It can be a lot of fun, and your creations are something that should make you proud. Whether you’re wanting to build that nice piece of furniture or just create something small and unique, keep reading to find out some helpful information about woodworking.
Whenever you plan to cut a narrow piece of wood, don’t use your fingers as a guide! The smart thing to do is to use another wood piece to push your wood up to the saw. This will assure you keep your fingers.
Every woodworking shop should have a stair gauge in it. They are used often to layout jacks for stairs, but they can also be clamped to your carpenter’s square. You can then use your square as a guide for a circular saw. You can always make perfectly straight cuts by using this method.
Many people use utility knives to cut veneer. This can be very dangerous; however, take heart, there is a better way. When cutting veneer, consider using a rotary cutting tool. These inexpensive tools can be purchased in your local fabric shop. Rotary cutting tools allow you to trim veneer to the perfect size.
If you find that there is rust on any of your woodworking tools there is a rather easy solution. As long as the rust is just on surface, all you need to do is use a pumice stone on the spot. Be sure to scrub gently, as being too rough can lead to you damaging the tool itself.
Plan out your project and go over it a few times before you start. This will help prevent you from making mistakes that will ruin your project. You do not want to start it all over again, so plan it out well before you cut, screw or nail anything together.
Always check your tools before you begin using them. Woodworking with a faulty or overused tool can easily lead to a serious injury or destruction of your materials. To make sure that this does not happen to you take the time to thoroughly inspect your tools from top to bottom.
Sanding blocks are essential woodworking tools. You can create easy to reuse sanding blocks of your very own by simply cutting three-quarter-inch scrap lumber into rectangles measuring 4.75 x 4.50 inches. Cut pieces of cork tile to fit each block. Spray both the rectangle of wood and the rectangle of cork tile with adhesive and press them together. Allow to dry, then spray the backside of an entire sheet of sandpaper with adhesive. Place your newly made block on the sandpaper with the cork on the down-side. Allow to dry and then use a utility knife to cut the sandpaper around each block.
Choose the type of wood that is right for the project you are planning. Soft wood isn’t ideal for tabletops because it scratches easily. Remember that different varieties of wood have different colors when they are finished.
Go to the art supply store and get a drafting square. Carpenter squares are a hassle, and drywall squares are notoriously inaccurate. When you need an exact square several feet in width and length, a drafting square is a surefire winner. Once you use it a few times, you’ll likely use it just as much as a tape measure.
Stain only provides color to wood, not finish. You will need to apply a finish coat on top of the stained wood. If you are in a hurry, or short on time, you can use a product that combines both stain and finish together. Be sure to use a higher-quality brush for this, and stain in the direction of the grain.
You can make a customized color of stain, but make sure the stains you are using are from the same manufacturer. Be sure that you use either all water-based stain, or all oil-based. Never mix the two. Finally, be certain to write down the exact amounts you used of each, so that the color can be duplicated if desired.
If you want to stain your wood piece, make sure to use a finer grit sandpaper if you want a lighter color. That is because the big scratches left by coarse paper allows more of the pigments to saturate the wood surface. Therefore, if you want the color to be lighter, make sure you’ve sanded with fine sandpaper.
Make sure there are no spots of glue on the wood before proceeding to finish your project. The spots will show up as lighter spots after the finish has been applied. You can use mineral spirits of naptha to completely remove all traces of glue from the wood. You may also be able to remove the glue by sanding the wood.
If you are new to woodworking, start small. Although you may be tempted to dive in to a difficult project, it is best to start small and slowly build your skills. Consider building a birdhouse or a shelf to help you learn your way around your woodworking shop and tools.
Make sure that your work area is always clean and organized. It is easiest to work when you know where everything and you do not have to work around a mess. To keep your area nice at all times you should put things away as you work and discard waste as it is produced.
It goes without saying, you should always be sober when pursuing a woodworking project. Even one beer or glass of wine can interfere with your reaction time and your ability to make sound decisions. If you are using any medication, prescription or over the counter, be sure to heed safety instructions regarding the operation of power tools and machinery.
Practicing your woodworking skills is what is going to get you further in the field. If you really want to create those unique pieces, then you’re going to have to put in some time. Don’t think about it as hard work, but instead use the tips that have been discussed to have fun and relax while enjoying your creations and time spent.