The world of woodworking ranges from creating benches to bridges and everything in between. That means there is a huge cache of knowledge out there just waiting for you to tap into it. Take your time and read this article in full to learn some new tips and tricks.
Take care when using power tools. If you are new to woodworking, be very careful when you are operating power tools for the first time. Read the manual thoroughly, and if possible, have someone with experience demonstrate how to use it properly. This will ensure that you don’t have a nasty accident during your woodworking project.
You should always test stain on a small area or on a wood scrap. By doing this, you can prevent unwanted surprises in the event that the stain color turns out differently than you expected. Wood and stains can surprise you, so test things out before you put it on the final project.
Woodworking can be expensive. The actual wood is one of the most expensive parts of any project. The rest of the cost is usually labor, glue and hardware. Sometimes you can save some money by buying a cheaper grade of wood for areas of your project that are not visible. Areas like drawers, backs and bottoms are excellent places to use this wood.
In a pinch, you can use a hacksaw blade as a makeshift compass. Often you can’t find a compass when you need it in room, when you are away from your shop. You can quickly nail a hole in the middle of a hacksaw blade, then steady the pencil against the proper tooth to get the right length. Draw that circle.
Ask for a how-to demonstration when you rent a new tool. Many times, they have specialist that can give you some great instruction. If you ask, they might have a list available with some other tips to help you later.
When sanding a piece of lumber, a lot of sawdust and debris is produced. To help remove those bits of dust and debris from your project vacuum the area. Then, remove the remaining debris using a tack cloth. Wipe both sides of the lumber to remove all traces of debris for best results.
If you will be re-coating an existing finish, be sure that the surface is clean and free of any wax or oils. Then, let it dry completely, and lightly scuff the surface with a 220-grit sandpaper so that the finish you are applying will have something to hold onto.
Always put your safety first when it comes to using tools, stains and paints. The more variety you use, the more specifics there are about applications, tool use, times for drying, and more. Put your safety first by reading the instructions, wearing any necessary protective gear, and working in areas with good ventilation whenever using oil-based products or anything that produces air pollutants.
Always use the safety equiptment that came with any of your woodworking tools. You may feel that a sheild is getting in your way when you are sawing, but its purpose is to protect you from serious injury. If you feel tempted just think of what it would be like to lose a finger or worse.
Stir, never shake stains and finishes before use. Over time, these settle, so mixing is necessary. Shaking, however, adds bubbles and doesn’t always mix the stain or finish thoroughly. Stirring mixes the products better by evenly mixing in any settlement that occurred during storage. Stains and finishes that are not mixed thoroughly will not apply correctly to the wood you’re staining and are at risk of looking blotchy.
Sometimes a little bit of glue is better than a clamp. Every woodworking shop should have a hot glue gun. Hot glue will hold small pieces better than any clamp ever could, if you could even maneuver one in place. When you are done, just gently pry loose with a putty knife.
Learn about using pilot holes. This is pretty simple to do. When driving a screw or hammering a nail into a little piece of wood or getting pretty close to the edge of a piece, it tends to split. Sometimes it’s unavoidable to put a fixing into a place like this. However, drilling a hole through the joint that’s a bit smaller than the fixing can prevent it from splitting.
Always check your tools before you begin using them. Woodworking with a faulty or overused tool can easily lead to a serious injury or destruction of your materials. To make sure that this does not happen to you take the time to thoroughly inspect your tools from top to bottom.
Only cut using sharp tools. Older and dull tools result in tear-outs and even chipping, which is frustrating and a waste of time. Sharp tools means you get clean cuts quickly. You’ll also spend a lot less time sanding things to get just the right look and fit that you need.
If you are working on your projects in your garage, keep your garage door open. You will be created a lot of wood dust. An open garage door allows your work area to be properly ventilated. Also, during the day, you work area will be better lighted with the garage door opened.
Wood is an expensive material to work with. It becomes really expensive when you are working on larger projects. Save some money by using cheaper and less attractive woods for areas of the project that are not on display. Save the high quality wood for the structure, tops and front of the project.
When using a table saw, use a block of wood clamped to the fence to set your length. Using the fence directly could result in a board being kicked back at you. To make measurements easy, use a block that is exactly 1 inch in length. Then all you have to do is set the fence length 1 inch greater than your desired length.
Whatever you do when it comes to woodworking, it is important that you take the time necessary to learn as much as you can. Read articles written by experts, like this one, and learn from your peers. The more you know, the better your projects will end up once done.