Woodworking is a craft like no other. You get to work with one of nature’s most useful resources and make something with your mind and hands. Whether you do this personally as a hobby, professionally for money or are just reading about it as a future possibility, this article has tips you can use to be a better woodcrafter.
Use stop blocks to your advantage for more accurate work. When cutting a lot of pieces the same size, no matter how carefully you measure, you often find small variations. Use a pre-cut stop block to make those measurements pinpoint accurate. Then the table saw will stop at just the right length length.
Even if you have been doing woodworking for some time you may want to consider taking a class. There are different levels of classes available, so you should be able to find one that teaches you something and is challenging. There is never too much that you can know about woodworking.
Try using duct tape to create a level spot. If you’ve used your table saw on a base that’s mobile, you should be able to easily pull it in and out. To really finish it up, find a level spot on your floor. This also helps you saw boards without obstruction. Mark your wheel positions using duct tape that is brightly colored, and then roll the saw to that same flat spot each time you need to saw.
Keep the floors safe in your woodworking shop. Dust builds up on the floor, making it dangerous for walking. Coat the slippery areas of your shop with a mixture of crushed walnut shells and paint. The walnut shells are just the right consistency to keep the floor rough enough for walking, even when sawdust builds up.
Never skip sanding when it is necessary or think that staining hides imperfections in the wood. Wood with scratches, dents and nicks absorbs much more finish or stain than wood that is smooth. When you skip sanding or do not do a thorough job of it, the imperfections stand out even more because of the increased absorption.
Before you start any woodworking project, get all of the tools you will need for the project ready. Always remember to bring a calculator and tape measure with you when you go to purchase your wood. Make sure you have any specialty tools you will need for your project available as well.
Take baby steps when first starting out with woodworking. It’s a lot of fun to learn, but woodworking is also pretty dangerous if you get too cocky too soon. Even when you feel like you know the basics, keep practicing them. And always where safety gear. You are much better off.
Make sure you buy the right tool for the job. When you are building a wooden deck onto your house, it would be difficult to do all the cutting with a hand saw. Instead, you should cut with a circular saw. A circular saw is electric; however, a hand saw is not.
Never allow someone to watch while you are woodworking without wearing the same gear that you are wearing. Being anywhere near the tools is a hazard, even if they are not using them. Wood or parts of the tool could fly into the air and strike them just as they could you.
When wiping excess stain off wood, wipe in the direction of the grain. Otherwise, the stain will just lay on top. Not only does this ensure that the stain is getting all the way into the grain, it will show off the grain of the wood to its best advantage.
Always wear protective glasses when using any type of saw, and ear protectors as well when you use power equipment. Chips and sawdust can destroy your vision if even a small piece flies into your eye. Woodworking is a great hobby, but it is important to stay safe while you work.
Be sure to keep all of your old cans of stain. Stain is expensive, and can come in handy if you wish to use a particular color again. Additionally, stains do not set up like finish does. If there is a skin on top, remove it, and the stain is as good as new.
Sometimes a retractable tape measure is seen as too unreliable for woodworking. The tip can get worn out or bent, making measurements inexact. While a good steel ruler may be best, you can use a tape measure for some jobs. Just make sure you use the same one for all measurements. Don’t switch tape measures.
Make planning something that takes as much time as the doing. Seriously, when you plan things out, you are less likely to make mistakes and your “doing” time will be a lot shorter. Some people find planning to this extent boring, but the simple fact is it can save you money and time overall.
If you are in the market to add to your woodworking tools you should try to save money by looking for used tools. It can be rather easy to find these tools on various resale websites, or you may even be able to find a site that caters to woodworkers specifically in your area.
Use duct tape to easily mark level areas of your floor. If you have a table saw or other large tool on a mobile base, it can be hard to find just the right spot on your floor to keep it level. Once you have found a level location, place tape around the wheels or base of your tool so that you can easily position it the next time it is out.
The craft of woodworking is unlike most others. It is a medium where humans take a strong natural resource and work in ways that leaves anything from pieces of art to buildings. Whatever your personal level of involvement in woodworking is, this article had tips and tricks in it you can surely use.