Look around as you move throughout your day. You see examples of man’s mastery of woodworking everywhere. From mailbox posts to pieces of furniture and art to full buildings, the power to use wood to create is a reason why civilization even gets to exists in many corners of the world. If you want to empower yourself with this skill, keep reading.
Anytime that you begin a new project you must consider your safety first. Be certain you always have the right safety equipment, and use your tools properly. Don’t ever remove the guards from your power tools; they are in place for your protection. You can’t complete the project if you end up hurting yourself.
Stair gauges may be just the ticket for crosscut guides. Clamp your carpenter’s square to your stair gauges while ensuring they coincide with the rise and run of your stair jack. After this, you will have to mark each of the notches. If you put them on the same tongue of your carpenter’s square, the combination that you can make will be a great circular saw crosscut guide.
Whenever you work with power tools, be sure your clothing is tucked in properly. Any loose clothing or long, dangling hair or jewelry can easily become tangled in the tool, leading to injury or other disaster. Tuck everything in, pull back your hair, take off dangling jewelry and then get down to work.
Make sure your workbench is the proper height. It really can make a big difference. It needs to fit you and how you work. Usually if you are around 5’6″ to 5’9″ you probably need one that is between 33″ and 36″ high. If you are 5’10” or taller, you may need one that is between 35″ and 37″ high. Use your bench at its current height to determine if you need to change it to work better for you.
Be safe when you first start out in woodworking. Wear the proper safety clothing, including goggles. You may feel silly, but you are dealing with sharp tools and splintering wood. These are things that can cause significant injuries to even the most seasoned woodworker. So be safe, and make sure all that are around you are safe too.
Glue can cause nasty stains on your finished work. You can eliminate stains easily using a piece of tape. First, clamp your wood together without any glue. Put a piece of tape over the joint. Cut the tape on the joint with a sharp knife. You can now clamp the wood together with glue and any excess will ooze onto the tape, not the wood.
If dust and dirt get into the holes of a brad or nail gun while they are not in use, this can cause them to wear out more quickly. It is a good idea to plug the air inlet holes up with something to prevent anything from getting in there.
You can prevent glue stains by placing masking tape along the joints of wood being adhered. First, tape the wood together along the joint, then use an Exacto knife to cut through the tape at the joint line. Following this, glue the pieces of wood together and clamp them. Just before the glue has dried completely, you can peel the tape off.
Try to keep your work area clean as much as possible. There is going to be a lot of wood dust on the floor. Pieces of wood debris may be strewn about. When you keep your work area clean, you reduce the occurrence of injuries. Always keep a broom, dustpan and a large trash can on hand.
Many professional recommend finishing the separate pieces of the project before it is assembled. This method makes finishing much easier and if the wood shrinks a little in the future, there will be no bare wood exposed. However, it is important to keep the finish off any surfaces that will be glued.
When using a water based stain or finish to raw wood, it is a good idea to raise the grain first. Apply water to the surface just before the final sanding and wait until it dries. The wood fibers will stand and you can remove them with minimal sanding before applying the finish.
Use hot glue instead of a clamp on small projects. If you have to cut, shape, or file a small object, try using a hot glue gun to attach it to a pedestal. It will hold better than a clamp, and can be used on projects that are too oddly shaped or small to be clamped in the first place. To remove it, simply pry lightly with a putty knife.
Choose a woodworking project that interests you. There are almost an infinite number of possible woodworking projects you could do. Picking a project that interests you and that you can get excited about makes it more likely that you will finish the project. Starting small, with an indoor project, is a good way to get your feet wet.
Some woodworkers look for perfect boards with no knots or blemishes for their projects. Using imperfect boards can add character to the finished piece so long as the defect does not compromise stability. Wood that shows whorls or burls can be used to create beautiful pieces that demand a high price when sold.
Be sure to teach any children that may have access to your woodworking space the dangers of touching your tools. Those tools can be so dangerous that a child could be killed if they try to use them without the needed supervision. Even if you lock this space still teach them about the dangers to be on the safe side.
Now that you have read this article, you know a few things about getting started successfully in woodworking. Use the ideas here to do a project that improves your life. Perhaps you build yourself a deck. Maybe you give new life to a piece of furniture someone got rid of. Whatever your inspiration, this article gave you the knowledge to get some woodworking done!